![mac mini 2011 fan replacement mac mini 2011 fan replacement](https://i.imgur.com/4E8GL9Ml.jpg)
- MAC MINI 2011 FAN REPLACEMENT SERIAL NUMBER
- MAC MINI 2011 FAN REPLACEMENT BLUETOOTH
- MAC MINI 2011 FAN REPLACEMENT SERIES
- MAC MINI 2011 FAN REPLACEMENT MAC
MAC MINI 2011 FAN REPLACEMENT BLUETOOTH
It is still attached to the AirPort/ Bluetooth board. Slightly lift the antenna plate from the end closest to the RAM.Ĭarefully pull the antenna plate away from the circular rim of the outer case. The antenna attaches directly to the hard drive (red markers), therefore attaching the antenna can move the hard drive around and loosen the connection of the hard drive cable to the logic board. If the screw holes don't line up with those on the hard drive, make sure that the two pins that are in the back of the hard drive are properly seated in the holes at the back of the case, above the housing for the second hard drive. It can be difficult to get the hard drive seated correctly such that the antenna plate fits in place correctly. Two 5.0 mm T8 Torx or 2.0 mm Hex screws (either screwdriver will work) Remove the following screws securing the antenna plate to the mini: Rotate the cowling away from the outer case and remove it from the mini. Lift the cowling from the end nearest the antenna plate. Remove the single 3.5 mm T6 Torx screw securing the cowling to the heat sink.
![mac mini 2011 fan replacement mac mini 2011 fan replacement](https://ae01.alicdn.com/kf/H0b5b566f74fd4aac94f917d8058b9096t/Brand-New-Genuine-922-9557-922-9953-for-Mac-Mini-Unibody-Aluminum-A1347-CPU-Fan-Cooling.jpg)
Lift the fan out of the mini for enough clearance to access its connector.Ĭarefully pull the fan cables upward to lift the fan connector up out of its socket on the logic board. You need only raise the fan enough to lift it off the standoff screw. Removing the standoff screw is not necessary to remove the fan. Lift the ear of the fan nearest the RAM up off the standoff secured to the outer case. Remove the two 11.3 mm T6 Torx screws securing the fan to the logic board near the antenna plate. Remove the bottom cover and set it aside. Tilt the mini enough to allow the bottom cover to fall away from the outer case. You do not need to apply much downward pressure while turning. Rotate the bottom cover counter-clockwise until the white dot painted on the bottom cover is aligned with the ring inscribed on the outer case. Place your thumbs in the depressions cut into the bottom cover.
MAC MINI 2011 FAN REPLACEMENT MAC
工具: 2 mm Hex Screwdriver (1) Mac Mini Logic Board Removal Tool (1) Spudger (1) T6 Torx Screwdriver (1) T8 Torx Screwdriver (1) Replacing this component requires removal of the logic board and most other components in your mini. 介绍 Use this guide to replace your mini's IR sensor/sleep LED assembly. Late last year, Apple announced a replacement program for certain hard drive components in iMacs sold between 20.Mac Mini Mid 2011 IR Sensor Replacement Replace a broken IR sensor/sleep LED. This is not the first time that iMacs have seen component issues worthy of a replacement program. Additionally, if an affected iMac user had their graphics card already replaced at cost, the customer is said to be eligible for a refund.
MAC MINI 2011 FAN REPLACEMENT SERIAL NUMBER
If the iMac falls within one of the above the serial number categories and is confirmed to have the graphics card issues, Apple will replace the AMD card free of charge up to three years from the computer’s purchase date. The last four characters of the serial number must contain one of the following groups (for example, xxxxxxxxDHJQ):
![mac mini 2011 fan replacement mac mini 2011 fan replacement](https://medias.sosav.fr/images/guides/big/b6xef7fm5unktlo.jpg)
Additionally, the iMacs must fall in the following serial number configurations: Above is a YouTube video demonstrating some of the noted issues. The problems have been documented over the past couple of years on Apple’s own Support Forums.
MAC MINI 2011 FAN REPLACEMENT SERIES
AppleCare, Genius Bars, and Apple Authorized Resellers have been given a series of steps to verify if a customer’s iMac exhibits the graphics card issues. iMac computers with affected video cards were sold between May 2011 and October 2012.Īpple says that the issue is connected solely to 27-inch models with 3.1GHz quad-core Intel Core i5 or 3.4GHz quad-core Intel Core i7 processors. Apple says that AMD Radeon HD 6970M cards (both 1GB and 2GB configurations) in select versions of these 2011 iMacs could fail:Īpple has determined that some AMD Radeon HD 6970M video cards used in 27-inch iMac computers with 3.1GHz quad-core Intel Core i5 or 3.4GHz quad-core Intel Core i7 processors may fail, causing the computer’s display to appear distorted, white or blue with vertical lines, or to turn black. This iMac was sold between that month and October 2012 when Apple launched thinner models with new internals. The iMac in question is the model released in May 2011 with Sandy Bridge processors and Thunderbolt ports. Apple has opened up one of its rare replacement programs for the graphics card in some mid-2011 iMac configurations, according to a notice issued to Apple Support employees.